Subwoofers u don't see everyday!!!

[ghostman]

Digital Designs Audio 9500h Series Features
http://i1220.photobucket.com/albums/dd454/snowman1011/081.jpg
9500h Series Features
If you're ready to get serious we've got the sub for you. Voted one of the Top 10 Most Baddass Subs of All Time, the 9500 has shown phenomenal performance in competition and daily ground pounding. The legend of the 9500 has spread mainly through word of mouth advertising, proving it stands up to today's real world demands on a true high performance woofer. The 9500h has all the features of the 3500f series with the additions of a stronger/ taller motor, stiffer suspension, and more voice coil options. There can be only one - the DD9500.
SPECIFICATIONS
Voice Coil Diameter 3.0"
Magnet Weight 406 oz
Power Handling RMS/Peak 1500/6000
Suspension Travel 80 mm
Nominal Impedance DVC .5, DVC .7, DVC 1.0, DVC 1.5, DVC 2.0, DVC 4.0 Ohm
Model 9510h, 9512h, 9515h, 9518h
MSRP 10"-$625, 12"-$649, 15"-$699, 18"-$749
DC Audio
http://i1220.photobucket.com/albums/dd454/snowman1011/lv5.jpg
A lot went into the design of this sub. We wanted an SPL sub without the drawbacks that some of the others encounter.

We had an idea, it was a sub with sick amounts of magnetic force but with a large gap
and cooling. This is something you don't see from other companies. But why would we be different? The answer is less coil failures and less re-cones. The only drawback (if it is one) you need a 73lbs motor to get the job done. Was it worth it? Yes it was!
The end result is a sub that has extreme amounts of output for the SPL lanes but reliable enough for a high-powered daily system.

When it was all done we ended up with a 73lbs triple stacked 1" slug, FEA optimized monster. We use a 8-layer flat wound 3" coil. Its available is D1ohm or D2ohm configurations. We also use upgraded multiple progressive spiders, upgraded cones, surround, lead wire, a cast basket and push terminals.

Key Features
• Extremely rigid non-pressed paper cone assembly
• Multilayered polymer foam surround
• Polypropylene dust cover with embossed DC logo
• 8”OD semi cup progressive roll spiders
• Extra heavy duty interweaved tinsel lead wire
• Cast aluminum black frame
• FEA analyzed and optimized motor assembly – Fully CNC machined
• Rubber mounting gasket
• Chrome spring loaded push terminals
• Dual 1ohm or 2 ohm 3” 8 Layer Hi-temp Aluminum voice coil wound on black anodized voice coil former

LV5
12"
15"
18"
Mounting Depth
8.25
9.5
10.5
Mounting Hole Diameter
11"
14"
16.75"
Motor Width
9.84"
9.84"
9.84"
Weight
78lbs
78.25lbs
80.5lbs
VC Diameter
3" Flat 8 layer
3" Flat 8 layer
3" Flat 8 layer
Displacement
.20³ ft
.24³ ft
.26³ ft
Magnet Weight
73lbs
73lbs
73lbs
Power Handling RMS/Peak
2000/4000
20,000 burst
2000/4000
20,000 burst
2000/4000
20,000 burst
Impedance (Ohm)
d.7, d1, d1.4, d2
d.7, d1, d1.4, d2
d.7, d1, d1.4, d2
Sd
494.00 cm²
791.00 cm²
1159.00 cm²
RE Audio MT
http://i1220.photobucket.com/albums/dd454/snowman1011/woofers_mt_big03-1.jpg
http://i1220.photobucket.com/albums/dd454/snowman1011/woofers_mt_big02-1.jpg
Designed for a single sonic goal: "To be the ultimate in SPL." The MT SERIES is built for brutality.

Sizes: 10", 12", 15"," and 18" (Customizable coil options)

Kraft Pulp Cone w/Carbon Fibers in Matrix
Rubatek Foam Surround
Cast Aluminum Basket
Foamed Core Dust Cap
Tork-Tite Terminal
8-layer Aluminum Voice Coil
FEA Optimized Motor Structure
Triple Stack Magnets
Dual, Triple, or Quad Progressive Spiders
Wrap Around Rubber Gasket
Sound Solutions Audio Z con
http://i1220.photobucket.com/albums/dd454/snowman1011/ZCON-18__87268_zoom.png
http://i1220.photobucket.com/albums/dd454/snowman1011/ZCON-18_07__02466_zoom.png
A true heavy weight by all accounts, the new SSA Zcon is absolutely a beast. After 3 years of development, to answer the demand from the mega power fanatics and high output crowd, the massive SSA Zcon is finally here. Incorporating an FEA optimized motor with a spiral CNC-machined solid pole piece, the Zcon has the technology and cooling to take some serious abuse with the ability to step up the cabin pressure to brutal levels.

Bringing to market our biggest motor ever, the Zcon has the motor strength for accurate cone control showing that this is not a one note wonder. The Zcon is at home in a moderate daily driver system as it is in a mega power competition system. Five sandwiched spiders and a large 3" - 8 layer aluminum coil, means the Zcon can handle the heaviest of hands on the volume knob for years to come. Right from the start, the Zcon is already in the top offerings on the market for the high end, big output daily driver sub woofers. You can be proud to own a SSA Zcon, as with the entire SSA speaker line up, it is designed, engineered, machined and built here in the USA.

D1 / D2
FS: 32 / 31.2
DCR: .7/coil / 1.4/coil
QMS: 7.59 / 7.76
QES: 0.31 / 0.31
QTS: 0.32 / 0.32
MMS: 323 / 338
SD: 1210 / 1210
VAS: 139.3 / 139.3
SPL: 94.9 / 94.5
BL: 17.74 / 25.2
XMAX: 29 / 29
POWER: 2250w RMS
Ascendant Audio Mayhem
http://i1220.photobucket.com/albums/dd454/snowman1011/mayhem18inchlargefront__37984_zoom.jpg
http://i1220.photobucket.com/albums/dd454/snowman1011/mayhem18inchlargeside__07093_zoom.jpg
The Mayhem Series of subwoofer utilizes many technological advances to create the toughest daily driving sub on the market. Our engineers have spent hundreds of hours analyzing the various failure modes of other drivers and producing new technologies and solutions to prevent these problems. Starting with our patent pending Helicool motor system, air is forced through axial cooling channels each time the cone moves. This positive displacement of air over the coil means increased thermal capacity and power handling. Using our proprietary suspension assembly techniques, we laminate multiple progressive spiders together for exceptional durability. Our specially formulated adhesives and adhesive agents have been specifically designed to handle high heat and mechanical stresses of 2500+Watts of power. The 30mm of Xmax ensures extreme linear ability and monsterous deep bass while the high motor force ensures plenty of skull cracking upper bass as well.



The Mayhem Series is the ultimate in bass performance.

Brutal Streetbasser
12", 15" and 18" Dual 2 Ohm models.
Triple stack FEA optimized motor
3" 4 layer aluminum coil
Triple layer reinforced collar
Five progressive spiders
Ultra rigid reinforced cone body
Hybrid foam surround
Cast Alluminum basket
Wrap round rubber gasket
Silver 8AWG Push terminals
2500W RMS


Thiele-Small Parameters
18"
Coils Dual 1 Ω / Dual 2 Ω
Re
0.7 Ω / 1.4 Ω


Fs 33.7 Hz / 33.2 Hz
Qms 6.52 / 6.62
Qes 0.29 / 0.27
Qts 0.28 / 0.26
Mms 307 g / 317 g
Sd

1210 cm^2


Vas 148.9 l
SPL 94.8 / 94.9 1W/1m
Bl 17.7 / 26.2 Tesla Meters
Xmax 30mm (one-way)
RMS 2500w

[ghostman]

Fi Car Audio BTL N3
http://i1220.photobucket.com/albums/dd454/snowman1011/BTL-N212_170x356_170x356.jpg
The BTL-N3 series is designed with SPL applications in mind. Utilizing three of our BTL Series high grade Neodymium magnets attached to a unique in-house CNC machined steel structure for extreme flux flow, the BTL-N3 Series is the latest weapon in our arsenal directed towards competition use. Massive 3" coils with thick coil winds handle extreme power and high current situations with ease. With 5-7 spider integrated suspension packs there is no lack for mechanical control. With over dozens of different option combinations to choose from, we can build the exact sub you need to fuel your SPL fire.
BTL Series: 12”, 15”, and 18”
Dual 1 and Dual 2 Ohm (custom options available)
Cast basket
Wrap around gasket
Kraft pulp fiber reinforced cone
Single layer wide foam surround
Push terminals
16 integrated leads
FEA optimized motor
High Flux density design
3” diameter 8 layer coil (High Xmax coil option)
Triple Neodymium high flux magnets
5-7 progressive spiders packs
Optional Heli-cool system
Tri-flow integrated heatsink
And many other custom options
Sundown Audio Nightshade Series
http://i1220.photobucket.com/albums/dd454/snowman1011/SA-10-01__41996_zoom.jpg
The SA-10 was designed to be an excellent sounding subwoofer that is equally at home sealed or ported. We feel that the SA-10 is one of the best woofers available in it's price category and will satisfy the needs of a wide variety of users ranging from bass-heads to audiophiles!

Based on the same motor and soft part platform as the larger SA-12 you can expect all of the great performance that the SA series has been known for since it's introduction now in a 10" package.

Sundown Audio SA-10 10" Subwoofer
Dual 4 Ohm Voice Coils
Tinsel Leads Secured to Spider
Strong Adhesives and Materials
600 Watt RMS Power Handling
SPECS ON D4 Model :

FS : 31.6 Hz
Qts : 0.45
Qes : 0.49
Qms : 5.64
VAS : 21.9 L
Mms : 187.4 g

Mounting depth = 6"
Cut out is 9 3/16"
10 3/8" OD with gasket

Crossfire Audio XS15D2-v2
http://i1220.photobucket.com/albums/dd454/snowman1011/xs15d2v2.jpg
http://i1220.photobucket.com/albums/dd454/snowman1011/xs15d2v3.jpg
Competition Worthy XS Subwoofers

Are you one of those people who can't enough bass? Then look no further than Crossfire's XS15D2-v2 competition subwoofer. This bad boy doesn't joke around when it comes to raw power, with a power rating of 2000 watts RMS this woofer is ideal for those who are a little more serious about their bass. Its kraft pulp fiber reinforced paper cone and foam surround provide stiffness, rigidity, and increased performance and quality of sound reproduction. Its 240 oz double stacked magnet structure provide the driving force need to move this woofer. The woofer also features quad progressive spiders and heavy-duty vented cast aluminum frame that are able to handle extreme SPL conditions. If you need bass and you need it now then the XS series subwoofer is the way to go.

15" Dual 2 Ohm XS Series Subwoofer
Power Handling:
Peak/Tone Burst: 5000 watts
RMS: 2000 watts
Impedance: 2 Ohm
Kraft pulp fiber reinforced paper woofer cone material
Single-layer wide foam woofer surround
Quad progressive spiders for extreme SPL conditions
Heavy duty internally vented cast aluminum frame
Hybrid extended pole piece
Chromed top and back plate
Low-carbon CNC machined steel motor
Heavy duty tinsel lead wires
3" 8 Layer Dual 1 Ohm aluminum wire voice coil
Dual stacked 240 oz. magnet structure
Frequency response: 20 - 200 Hz
Sensitivity: 90.2 dB
Xmax: 26.7mm"
Mounting depth: 8-3/4"
Cutout dimensions: 14-1/8"
Authorized Internet Dealer
1-year Manufacturer's warranty
DAD Audio
http://i1220.photobucket.com/albums/dd454/snowman1011/BD_15_front_small.jpg

These are the bad boys; a serious woofer with serious performance.
Sizes available: 10 ", 12", 15"
1000 watts RMS/2000 watts peak
Dual 2 ohm copperclad aluminum voice coils
3" voice coil
Unique cast aluminum basket
Woven tensil leads
Non-pressed paper cone
4-layer UV treated surrounds
Poly-cosmetic caps on the front
Surround, cone, and caps stitched for extra strength
Conex spiders
Rubber gaskets
Nickel plated compression terminals
Low carbon steel top plates and t-yokes
Designed and handrafted in the USA
Real-world tested RMS power ratings
Sound Splinter RL-i 8 Single 4ohm
http://i1220.photobucket.com/albums/dd454/snowman1011/rli8__60094_zoom.jpg
SoundSplinter’s exclusive 8" driver is perfect for serious enthusiasts seeking phenomenal performance for any application involving limited space. We have designed this driver to perform in enclosures as small as 0.2 cu ft net volume. Coupled with the obscene one-way excursion potential of over 18 millimeters, as well as the ability to handle up to 500 watts, the RL-i8 will be able to contend with and in many cases put to shame, similar small drivers that cost twice as much! Available in dual and single 4.

T/S Parameters
Single 4

Qts:

0.217

Qes:

0.235

Qms:

2.798

Fs:

25.7 Hz

Re:

3.78

Ls:

2.022 mH

Lp:

3.859 mH

Rp:

3.786

Dia:
(% shift)

160 m

44.7 %

Vas:

23.44 L

Mms:

92.47 g

Cms:

412.8 u

Bl:

15.51 T*m

n0:

163.8 m

SPL:

84.14 dB

Sd:

0.020 m^2

RMS:

300 watts

Xmax:

18.3 mm

PSI Car Audio 12" Platform 3 Subwoofer
http://i1220.photobucket.com/albums/dd454/snowman1011/IMG_9791-Small.jpg
Our largest current offering, the Platform 3 series is a massive subwoofer, designed for massive amounts of output! The standard version of the Platform 3 is geared towards very loud, but still musical systems. It is designed to deliver everything from low octave, window flexing bass to throat tickling upper range bass frequencies.

Power Handling Ratings:
RMS Power - 2500 watts
Peak Power Handling - 5000 watts
SPL Burp Power - 8000

Standard features include:
Massive dual stacked 9" x 1" magnets
Chrome top and bottom plates
FEA optimized motor assembly
8 spoke aluminum cast frame - Black
Chrome push terminals
Extended length 83mm aluminum roundwire voice coil
Dual 1 and Dual 2 ohm standard impedances
Triple 8" progressive roll poly-cotton spiders
Dual sewn 3mm heavy duty leadwire
Kevlar impregnated pulp cone body
1.5" wide roll rubberized foam surround
6" polypropylene dome dustcap
PSI logo
T3 Audio T.S.N.S. subwoofer
http://i1220.photobucket.com/albums/dd454/snowman1011/001.jpg
http://i1220.photobucket.com/albums/dd454/snowman1011/thumb_003.jpg
The Overwhelming Choice Of World Champions
T3 Audio is known around the world as the leader in competition design and engineering. We are the innovators and want the world to know it. Every T.S.N.S. subwoofer we make is hand-built in the U.S.A. to the exacting specifications required for competition winning results. The DNA of a T.S.N.S. is entirely comprised of our proprietary parts exclusively designed, tooled, machined and assembled to be the most dominant subwoofer that money can buy. The 1,200 ounces of laser etched motor force, triple proprietary 10” diameter spider suspensions, 4” 4-layer flat wound aluminum proprietary dual voice coils (available in custom impedences) and composite high performance cones prove that this subwoofer is the result of years of constant over engineering. Four years of total domination in the SPL competition lanes and being recognized as one of the most reliable subwoofers at extreme power levels says it all. If you only settle for the best and second place is not an option ….. then the T.S.N.S. is your only choice.

Design
12”, 15” and 18” Subwoofers
Gun metal black 1200oz. motor structure
Optimized tri-path cooling system
T3 logo and TSNS machined into back plate
T3 Audio’s “Ouchman” machined into pole piece top
T3 logo and TSNS embossed rubber magnet boot
Unique cast aluminum basket
Rubber mounting top gasket with T3 logos
10” Triple spaced Conex spider suspension
T3 embossed dual spider spacer rings
Heavy gauge double flat wire sewn in tinsel leads
8awg Direct wire connections
Treated multi layer EES foam surround
1 Piece Carbon Fiber or Kevlar front cap with aluminum logo
Dual 2ohm Voicecoil/ Custom impedances available
4” Black anodized stainless steel coil former
CC-Aluminum flat wire coil 72mm height
5000w RMS/ 30,000w++ Tone Burst
Feared by many, respected by all!
Specifications
TSNS-12d TSNS-15d TSNS-18d
Total Weight (lbs) 86 88 90
Motor Weight (oz) 1200 1200 1200
Mounting Depth 9.90" 11.20" 11.80"
Basket Depth 4.70" 6.00" 6.60"
Magnet Depth 5.20" 5.20" 5.20"
Cutout Diameter 11.10" 14.00" 16.80"
Overall Diameter 12.76" 15.87" 18.55"
Magnet Diameter 10.60" 10.60" 10.60"
Spider Diameter 10" 10" 10"
Coil Diameter 4" 4" 4"
Displacement (ft3) 0.34 0.4 0.46
VIBE Audio BLACKDEATH15P
http://i1220.photobucket.com/albums/dd454/snowman1011/blackdeath15p2.jpg
http://i1220.photobucket.com/albums/dd454/snowman1011/blackdeath15p4.jpg
A Plague of Bass

A heavyweight subwoofer with every detail taken to the extreme to provide deadly bass. The Paper Composite Cone offers increased moving mass and extended low frequency reproduction, for low brutal street bass. The BlackDeath 15 is fully re-coneable making it perfect for competition use.

15" Black Death Series Dual 4 Ohm Subwoofer
Power Handling:
Peak: 7,500 watts
RMS: 2,500 watts
Minimum RMS: 1,250 watts
Impedance: 4 Ohms
Paper Composite Cone offers increased moving mass and extended low frequency reproduction
Hybrid multi-layer foam woofer surround has unique hi-roll geometry, allowing huge excursions of the woofer cone without decreasing vital cone area
Heavy gauged speaker cables directly connected to the voice coil
289oz. Double stacked magnet
3" vented aluminum voice coil
Frequency response: 15-850 Hz
Sensitivity: 93 dB
Cone Type: Paper Composite
AQ Audio HDC315 Copper Coil Subwoofer
http://i1220.photobucket.com/albums/dd454/snowman1011/HDC315_3.jpg
http://i1220.photobucket.com/albums/dd454/snowman1011/HDC315_1.jpg
The HDC3 series is the product of over two years of development and hundreds of hours of testing real prototypes in real boxes and real cars. The new HDC3 series has been a long time coming; you can’t simply buy some off the shelf parts, throw in some chrome; that’s not good enough, that’s what other companies do. Anybody can add some bling, make up some ridiculous claims only a noob would believe, publish a fancy web page with glossy pictures, throw in some fantastic sounding specifications the marketing department loves, raise the prices and hope you’re stupid enough to line their pockets with your hard earned money. Actually that philosophy works; many companies swear by it.The HDC3 is a powerful new design with increased cooling, more throw, stronger cone and can be ordered with a choice of several suspensions and coil options allowing you to customize the HDC3 for your particular application be it either great sounding street beating or all out gut wrenching SPL.The Standard HDC3 comes with your choice of dual 1 or dual 2 ohm four layer high performance copper coils, a vented extended pole piece with flared ends for increased cooling and less noise. The Standard HDC3 is optimized for the best combination of great sounding loud Everyday Street beating. for those who want an all out SPL machine flat wound Aluminum wire coils designed for maximum power handling and SPL applications are available as a low cost option.A high performance subwoofer requires a strong cone/surround capable of withstanding the huge motor forces applied without folding or separating from the coil former. It also must be light enough to not act as an inefficient power robbing, suspension killing glob of heavy mass requiring outrageous wasted power to set in motion. The HDC3 cone assembly is the perfect combination of weight, strength and profile combined with a high strength multi layer high excursion foam surround glued and double stitched for additional strength.
HDC3 SUSPENSION

Suspension systems are generally the weakest link in the chain of parts comprising a subwoofer design and often are the primary failure mode. Over time and especially with high power applications the spider or spiders, if the suspension has more than one or two, begin to sag and as a consequence the suspension can no longer control the coil movement which in turn makes the sub sound bad, the coil to rub and electrical shorts in the coil windings, with the resultant black smoke and nasty smell signifying the destruction of your subwoofer and the loss of your hard earned dollars. Did I mention that when spiders start sagging the TS specs so proudly listed on your new subwoofer bear little resemblance to the TS specs of your subwoofer when the suspension wears out?Suspension, especially in high power application, fail from glue joint failures at the spider/basket landing glue joint, the spider/coil former attachment surface area and the cone/coil former attachment surface. These last two glue joints are often referred to as the “triple” joint. WHY DO THESE GLUE JOINTS FAIL? It usually comes down to MONEY. Most manufacturers build the cheapest way possible and the cheapest and most practical method of making these joints is by MACHINE with the cheapest glues available. MACHINE gluing of these joints usually have no provisions for ascertaining proper penetration and saturation of glue at the joint area. Nor does the assembly method allow for the use of reinforcement of the joint with additional material. Under NORMAL usage MACHINE gluing and standard assembly methods are adequate. Unfortunately many of us push our systems to the limit and then some.We at Audioque are not satisfied with the NORM. We spare no expense and do everything we possibly can to prevent suspension failures. We use multiple spider configurations engineered and designed to maintain rigidity. We hand glue critical glue joints with high quality glues and provide additional reinforcement structures to the suspension components.
HDC3 DIRECT CONNECT LEAD WIRES=NO LEAD SLAP

High excursion subwoofers require a lead wire system that doesn’t flop all over the place or break. We use the direct connect system (no terminals) because it works the best. With our direct connect system you get no annoying lead slap noise, no ripped or holes burnt in the spiders and no flimsy lead in wires coming out of the cone to break or short out and burn into. You get no cheap terminals to break off or come loose. You do get 12 gauge lead wire easily connected by wire nuts or crimp connectors. You can also twist and tape the connections if you’re in a hurry.We have spared no expense to give you the best subwoofer value on the market today. We have sourced our parts and manufacturing with exacting standards for quality, durability and performance. In the process we regrettably have had to leave some of our former American partners to stay competitive with today’s market place. Our production costs have been brought in line with our competition but our operating margins remain the same. We have done what we consider unique in this business; we have shared our savings in production costs with our customers.Note: Parameters taken of random single sampling of NIB subwoofers with no pre-break-in. Parameters for 8-layer flat wound aluminum voice coils only. No multiple samples averaged.
Specifications
Model HDC310 HDC312 HDC315 HDC318
Woofer Size 10" 12" 15" 18"
Fs 41 Hz 34 Hz 40 Hz 35 Hz
Sd 33m M2 53m M2 89m M2 119 M2
Krm 11.76 mOhm 12.443 mOhm 12.686 mOhm .
Erm 0.881 0.88 0.875 .
Kxm 113.942 mH 118.004 mH 144.352 mH .
Exm 0.667 0.664 0.628 .
Vas 9.168 Ltr 14.170 Ltr 25.070 Ltr 56.54 Ltr
Cms 59.3 uM/H 0.05 uM/H 0.03 uM/N 0.04 uM/N
Mmd 239.556 g 251.649 g 253.635 g 457 g
Mms g 409.40 g 367.60 g 503.90 g
BL 24.114 TM 28.85 TM 18.32 TM 19.51 TM
Qms 6.999 7.652 8.651 9.198
Qes 0.374 0.385 0.652 0.633
Qts 0.355 0.367 0.612 0.592
Sensitivity 1W/1m 84.439 dB 83.62 dB 87.03 dB 88.30 dB
Magnet Diameter 8.7" 8.7" 8.7" 8.7"
Magnet Weight 340 oz 340 oz 340 oz 340 oz
Coil Diameter 3.0" 3.0" 3.0" 3.0"
Coil Length 2.135" 2.135" 2.135" 2.135"
Useable Throw 3.0" 3.0" 3.0" 3.0"
Continuous Power 1000 W 1000 W 1000 W 1000 W
Music Peak Power 2000 W 2000 W 2000 W 2000 W
Mounting Depth 7.625" 8" 8.875" 9
Circle Cutout 9.4375" 11.225" 13.8375" 16.65"
Model HDC310 HDC312-D1 HDC315-D1 HDC318-D1
Ascendant Audio SMD Series Subwoofer
http://i1220.photobucket.com/albums/dd454/snowman1011/smd15inchlargefront__16509_zoom.jpg
http://i1220.photobucket.com/albums/dd454/snowman1011/smd18inchlargeside__22354_zoom.jpg
The SMD Signature Series of subwoofers comes from working with Steve Meade and his monster installs for close to a decade. Seeing the progression of subwoofer and amplifier technology we have put pen to paper and designed several new technologies to help push things to the next level. Starting with the obvious, the motor, it is a Super Gauss dual flux path motor with incredible motor strength not before possible from a ferrite motor structure. Integrating our 4” EMB coil topology to the system provides electro-mechanical braking to linearize flux. Having all of this motor force and linearity are no good if you can’t handle power thermally. Every SMD produced spends a significant amount of time on one of our 4 axis CNCs machining the Dyna cool system into the internal parts of the motor structure. Utilizing cooling channels and specific paths in both the gap plates and pole piece we can extend the thermal capacity of the sub out to 3500W RMS in its normal range of musical operation. Keeping it mechanically under control is a 7 spider Tri-point suspension system with integrated lead wires capable of handling tremendous current.


All of these technologies culminate in the pinnacle of daily driving subwoofer performance. Working in ported enclosures much smaller than the average sub, you can get displacement never before possible in tiny spaces, often allowing you to step up to the next size driver for even more output capability.

4" ceramic coated coil
Super-Gauss motor technology
EMB flux linearization
Dyna-cool system
7 spider pack
Tri-Point suspension
Hybrid foam surround
Canti-Mount system
Foamed core dustcap
32mm Xmax
3500W power handling
Small ported applications
Thiele-Small Parameters
18"
Coils Dual 1 Ω / Dual 2 Ω
Re
0.7 Ω / 1.35 Ω

Fs 29.7 Hz / 29.7 Hz
Qms 5.45 / 5.43
Qes 0.32 / 0.32
Qts 0.3 / 0.3
Mms 521 g / 516 g
Sd


1210 cm^2

Vas 114.3 l
SPL 91.5 / 91.6 1W/1m
Bl 20.66 / 28.57 Tesla Meters
Xmax 32mm (one-way)
RMS 3500w
Incriminator Audio Warden Series
http://i1220.photobucket.com/albums/dd454/snowman1011/73981_441549962046_63027127046_5809335_4007716_n__ 62033_zoom.jpg
http://i1220.photobucket.com/albums/dd454/snowman1011/ia_warden__11630_zoom.jpg
After 5 years of work the Warden is finally here! The newly coming Warden is the next generation of all out SPL monsters – forget everything you’ve seen until this point. The Warden is the first True SPL subwoofer on the market that boost a steel top plate for maximum transfer of magnetic flux from the neodymium magnets to the gap which in turn equals more magnetic force to drive the cone to Extreme SPL levels. These six neodymium magnets act as one through one common top plate. Other subwoofers on the market have an aluminum top plate, which keeps the columns separated; this causes each column to independently transfer magnetic flux. This results in less SPL because the spaces between the columns do not transfer flux. For example if the Warden is say 500 horsepower in the gap, that power is constant, as the transfer of flux surrounds the coil and pushes and pulls on it with one authority. If the other unit was 500 horsepower too it would only be constant in the locations where the columns are located, the space between the two would be zero force, and the end result is less SPL.

The Warden has been lurking in the shadows for years, the rumors and myths that surround this driver have been circulating the internet for what seems like ages, but it’s finally here and we consider this to be our proudest accomplishment to date.


-Dual .7 and Dual 1.4 Standard or Other Custom Options Available
-Black Cast Basket
-3" 8 layer FlatAluminum Voice Coil
-Black Progressive Spiders with Woven Tinsels - Suspension Options Available
-Non-pressed Kraft Fiber Reinforced Cone Double Layer Foam Surround
-130 Oz Neo Column Magnets with Black Finish
-Interlocking Aluminum Spider Spacer Assemble
-CILD - Center Interlocking Dustcap Design for Easy Field Recones
-ADC - Air Driven Cooling - Six Column Vents for Max Motor Cooling
-Silver Push Terminals
-Wrap Around Rubber Gasket
-2500 Watt RMS Rated

[Jesse]

Nice

[ghostman]

Nice
thanks!;):cool:

[3tc power]

Aww man you forgot the nasty kove audio armaggedon subs. Oh and RE and Fi are designed by the same engineers.

[ghostman]

Aww man you forgot the nasty kove audio armaggedon subs. Oh and RE and Fi are designed by the same engineers.
Never heard of kove audio.:dunno: Who are they?:dunno:

[ghostman]

Aww man you forgot the nasty kove audio armaggedon subs. Oh and RE and Fi are designed by the same engineers.
They don't make kove audio anymore. There subs are rare to find now but yes those things were monsters.:cool:

[ghostman]

Aww man you forgot the nasty kove audio armaggedon subs. Oh and RE and Fi are designed by the same engineers.
U forgot one; Ascendant audio is own by Fi.;)

[De O]

Ok Mr Ghostman I got one for u since this look like its ur passion if u was to use one 15" sub what would u use?

[ghostman]

Ok Mr Ghostman I got one for u since this look like its ur passion if u was to use one 15" sub what would u use?
Oh that's easy. It would be RE Audio MT sub.:cool:

[Jesse]

Kicker L7 15in ftw.lol just my 2cent.

[ghostman]

Kicker L7 15in ftw.lol just my 2cent.
U just could not leave alone not even for one day! We know kicker is good but come on dude. Re audio MT, Ascendant Mayhem, and DD audio will kick kickers ass.:rofl::cool:

[Jesse]

Lol..cool, but go look up an c how much for dem speakers u talkin bout compare to a L7..

[ghostman]

Dude u can't be serious

[De O]

Oh that's easy. It would be RE Audio MT sub.:cool:

And how much would one cost?

[ghostman]

And how much would one cost?
It depends where you go. Because there only too sites that I know of sell Re audio Mt. www.sonicelectronix.com or www.woofersetc.com they go for $799.99 Right now sonicelectronix don't have any right now but again that's my preference It doesn't have yours u can buy what ever suits ur budget. But at the time sonicelectronix had them, u could make them offer and buy at ur talk down price.

But jesse talking on one side of his mouth ask he how much a kicker solobabric X cost. It just around the Mt's. So yea:cool:

[ghostman]

DD all the way...... There is no louder single sub on earth....
Thank you, Thank you, Thank you, Redbull, the only other subs that come closest to them is DB Drive, Incriminator audio, Fi car audio, Ascendant audio.

[MazdaKLZE]

Ghostman u should compare more affordable subs,like mtx9500,L5,L7,jlw7,alpine type r,Etc...At the end of the day,most people aint spending that kind of money on a sub,for everyday use..

[MazdaKLZE]

Thank you, Thank you, Thank you, Redbull, the only other subs that come closest to them is DB Drive, Incriminator audio, Fi car audio, Ascendant audio.

The hell with DB drive IMO!!They dont take the power they say they do,from my experience!

[ghostman]

The hell with DB drive IMO!!They dont take the power they say they do,from my experience!
Dude what's with you with this thing!!!! I believe u hook up something wrong that's why the sub blow. You is the only person I hear with this all the time. Well that's your opinion and I will respect it.:):):)

[MazdaKLZE]

Dude what's with you with this thing!!!! I believe u hook up something wrong that's why the sub blow. You is the only person I hear with this all the time. Well that's your opinion and I will respect it.:):):)

I know about 4 people that had problem with them.One partner home had it for one month,before it blew.He then purchase a Kicker L7,neva had a problem after that.He had it over 3 years now.This man warn me before i bought mines about them, but i didn't listen!!:no:

[ghostman]

I know about 4 people that had problem with them.One partner home had it for one month,before it blew.He then purchase a Kicker L7,neva had a problem after that.He had it over 3 years now.This man warn me before i bought mines about them, but i didn't listen!!:no:

Ok cool. I ask what u did tell what u did. Don't Tell anything bout partner. tell me ur experience. tell me what happen to u. Then I could see what happen and I can say yes is likely to happen:cool:

[ghostman]

I forgot this one Atomic Speakers
http://i1220.photobucket.com/albums/dd454/snowman1011/ele_10_12_15_big.png
Extinction Level Event Series - ELE 12

Quick Specs
2000Watts
SPL competition Woofer.
Cast Aluminum Basket
Double stacked magnet
3 inch heavy gauge high temp voice coil
Extreme long excursion
* Rigid Die cast aluminum basket
* Organic long fiber non-pressed cone body for accurate tight bass
* Highly damped Kevlar reinforced cone body
* triple layers foam surround increase the power capacity of woofer
* Extended neck joints on cone, coil and spider strengthen the integrity of moving structure for high power capacity
* Compressed mounting ring gasket
* vented coil for extra heat dissipation
* 3 inch high temp aluminum voice coil
* extended, machined cut one piece back plate
* Powerful 1 inch thick 90 oz high energy magnet
* over 2-1/2 inch long excursion motor structure
* reinforced resin impregnated polycotton spider extend the life span of the speaker from material fatigue and collapse.
* integrated heavy duty lead wire on spider prevent short circuit and melt down
* dome shape dust cap design
* low carbon front and back plate
* Vented magnetic gap technology
* Laser etched, machined and chromed back plate
* 2000Watts

[ghostman]

Ghostman u should compare more affordable subs,like mtx9500,L5,L7,jlw7,alpine type r,Etc...At the end of the day,most people aint spending that kind of money on a sub,for everyday use..
Y'all miss the point the thread is about subs u don't see regularly. That's what I'm saying. U all talking about subs people see all the time regularly. again u don't have to buy does series of subs. what I am showing is the best of the best from each company. SSA sub the I con cost little over a $100. so yea buy what suits your budget. And no I don't really rate jl audio like that. Simply they suck. Jl audio is a SQ sub there not for Spl. They not like kicker or mtx which are built to SQ/SPL.

[MazdaKLZE]

Older model Db drive Platinum series 12" sub,on a mtx 1501d amp.The box was the right specs for the sub.It lasted one week,before i blew the spider off of the coil,for the sub.I drive like 120 miles a day total,so i play my system hard for a long time.Mtx1501d specs is 500w in 4,1000w in 2..Db drive plw12d4 (4 ohm per coil)1000w rms,2000 peak.:dunno: Am running a md sound model MD12-12175 subwoofer ,with no problem right now.800w rms 1800w peak..2 ohm per coil

[ghostman]

^^^^Now I see the problem u had. platinum series had defects in them that's why db stop make them. That's why it blew, the cone was very weak. I remember the platinum series they had paper cone in them but it was to weak so when u start to play them for long periods it starts to rip and then they blew. the Platinum series weren't built that great. When I tell u tell me ur problem that's what expect to here So I can figure out your problem and be able to say what it is. Always Remember this when u buy a new sub allow some time for the sub to break in, Because if u don't u can blow sub like what happen with your old platinum series sub.

[MazdaKLZE]

^^^^Now I see the problem u had. platinum series had defects in them that's why db stop make them. That's why it blew, the cone was very weak. I remember the platinum series they had paper cone in them but it was to weak so when u start to play them for long periods it starts to rip and then they blew. the Platinum series weren't built that great. When I tell u tell me ur problem that's what expect to here So I can figure out your problem and be able to say what it is. Always Remember this when u buy a new sub allow some time for the sub to break in, Because if u don't u can blow sub like what happen with your old platinum series sub.
Mines wasnt that old.It wasnt the paper cone one. Like this one.Hard plastic in the middle.
http://g35driver.com/forums/attachments/archived-sales/76400d1189256151-db-drive-platinum-series-competition-system-mid-hi-amp-sub-amp-15-sub-plwwoofer.jpg

[ghostman]

your particular had a defects in them. That why db stop making.

[MazdaKLZE]

your particular had a defects in them. That why db stop making.

Makes alot of sense.It sound good too!

[ghostman]

Mines wasnt that old.It wasnt the paper cone one. Like this one.Hard plastic in the middle.
http://g35driver.com/forums/attachments/archived-sales/76400d1189256151-db-drive-platinum-series-competition-system-mid-hi-amp-sub-amp-15-sub-plwwoofer.jpg
In competition with the one you have use to get so hot they it burned out the cone and even catch fire. It doesn't happen with the WDX it's stronger.

[cruzan-s]

I know about 4 people that had problem with them.One partner home had it for one month,before it blew.He then purchase a Kicker L7,neva had a problem after that.He had it over 3 years now.This man warn me before i bought mines about them, but i didn't listen!!:no:

^True, very true!

[ghostman]

Now I see some one back up ur case.

[MazdaKLZE]

[QUOTE=ghostman;68043]Now I see some one back up ur case.[/QUOTE

Lmao

[ghostman]

[QUOTE=ghostman;68043]Now I see some one back up ur case.[/QUOTE

Lmao
But still db drive is a great sub. And the new ones don't have that problem anymore. But in the mean time check out http://www.soundsolutionsaudio.com/store/

[Jesse]

I know about 4 people that had problem with them.One partner home had it for one month,before it blew.He then purchase a Kicker L7,neva had a problem after that.He had it over 3 years now.This man warn me before i bought mines about them, but i didn't listen!!:no:

Just to add on to tht, my 2 L7 12's is a 08 model an second hand used and they still playin like they just outta the box believe it or not, so believe it or not they goin on almost 4yrs of usage..Good stuff. Big O just kno that if u go kicker u wont regret it, u should also be able to find some good deals over there so u straight..

[ghostman]

^^^ too add Re audio too there great.

[ghostman]

For the Kicker guys
Kicker L7 15s and 2500 watts
<iframe width="420" height="315" src="http://www.youtube.com/embed/79ae-fkPxoE" frameborder="0" allowfullscreen></iframe>
KICKER L7 15"s
<iframe width="420" height="315" src="http://www.youtube.com/embed/f6V05S8-rxo" frameborder="0" allowfullscreen></iframe>

[ghostman]

Re Audio MT
STUPID WINDSHIELD FLEX - 98 Civic 10,000 Watts 2 18's Rockford Fosgate!
<iframe width="420" height="315" src="http://www.youtube.com/embed/A98VDms0C6w" frameborder="0" allowfullscreen></iframe>